Skip to content
Switch article
Using OKPROXY on WindowsUsing OKPROXY on LinuxHow to Change DNS Settings

Using OKPROXY on Linux

Prepare a server that can run 24/7 as the encrypted proxy server. The server must use a Linux x86_64 / amd64 system.

OKPROXY encrypts mining data before sending it to the pool over the internet, reducing the risk of the data being identified or disrupted while traveling across external networks. Mining machines connect to the server running OKPROXY over a local area network (LAN). Make sure both are on a trusted LAN.

Run OKPROXY

  1. Download OKPROXY v2.1.0.
  2. Create an okproxy directory on the proxy server and place the downloaded okproxy file in it.
    sudo mkdir -p /opt/okproxy
    sudo cp okproxy /opt/okproxy/
    sudo chmod +x /opt/okproxy/okproxy
  3. Open the directory and run OKPROXY.
    cd /opt/okproxy
    ./okproxy
  4. Keep the terminal open while testing manually. For continuous operation, configure the system service under “Start OKPROXY at boot” below.

Configure the pool address

After OKPROXY starts, enter the proxy pool address in the miner dashboard or mining software. Use this format:

stratum+tcp://proxy-server-IP:port

For example, if the proxy server IP is 192.168.152.128 and BTC uses port 2222, enter:

stratum+tcp://192.168.152.128:2222

Supported coins and ports:

CoinPort
LTC1111
BTC2222, 228, 3367
BCH2233
ETC4444, 7777 (E9 only)

Assign a static IP to the proxy server

To prevent the proxy server IP from changing after a restart or network reconnection, assign a static IP to the server running OKPROXY:

  1. Check the current IPv4 address, gateway, and DNS.
    ip -4 addr
    ip route
    resolvectl dns
  2. Reserve a fixed IP for the proxy server in the router settings, or configure the current IPv4 address, subnet mask, gateway, and DNS as static in Linux.
  3. If the server uses NetworkManager, you can configure a static IP as follows.
    nmcli connection show
    sudo nmcli connection modify "connection-name" ipv4.addresses 192.168.152.128/24 ipv4.gateway 192.168.152.1 ipv4.dns "223.5.5.5 114.114.114.114" ipv4.method manual
    sudo nmcli connection up "connection-name"
  4. Check the server IPv4 address again to confirm that it is fixed.
    ip -4 addr

If the proxy server IP changes, update the pool address configured on every affected miner.

Network requirement

The proxy server and miners must be on the same LAN, with their Ethernet cables connected to the primary router.

Allow the proxy ports

Keep the Linux server firewall enabled. Allow only the proxy ports actually used by your miners; do not disable the entire firewall.

For systems using ufw:

sudo ufw allow 1111/tcp
sudo ufw allow 2222/tcp
sudo ufw allow 228/tcp
sudo ufw allow 3367/tcp
sudo ufw allow 2233/tcp
sudo ufw allow 4444/tcp
sudo ufw allow 7777/tcp
sudo ufw reload
sudo ufw status

For systems using firewalld:

sudo firewall-cmd --permanent --add-port=1111/tcp
sudo firewall-cmd --permanent --add-port=2222/tcp
sudo firewall-cmd --permanent --add-port=228/tcp
sudo firewall-cmd --permanent --add-port=3367/tcp
sudo firewall-cmd --permanent --add-port=2233/tcp
sudo firewall-cmd --permanent --add-port=4444/tcp
sudo firewall-cmd --permanent --add-port=7777/tcp
sudo firewall-cmd --reload
sudo firewall-cmd --list-ports

Start OKPROXY at boot

Use systemd to start OKPROXY automatically when the server starts.

  1. Create okproxy.service.
    sudo nano /etc/systemd/system/okproxy.service
  2. Add the following content and save the file.
    [Unit]
    Description=OKPROXY encrypted proxy
    After=network-online.target
    Wants=network-online.target
    
    [Service]
    WorkingDirectory=/opt/okproxy
    ExecStart=/opt/okproxy/okproxy
    Restart=always
    RestartSec=5
    
    [Install]
    WantedBy=multi-user.target
  3. Enable and start the service.
    sudo systemctl daemon-reload
    sudo systemctl enable --now okproxy
  4. Check the service status.
    sudo systemctl status okproxy
  5. To view the service log, run:
    journalctl -u okproxy -f